camaro rear end width

1993 Chevy 1500 4X4 need to know carrier size. The rear end appears to be a borg warner with a factory limited slip and with disk brakes.

1969 Chevrolet Camaro Rs Ss S83 1 Harrisburg 2019 Mecum Auctions

The 1970 rear end differs from the 1971-1981 rear end.

. Then you can mock them up in the wheelwells positioning them for good clearance desired ride height. Does anyone know if the wheel mating surface-to- WMS for 82-88 camaros are the sameand what the width actually is. So if your 67 has the stock rear they wont fit but if it has a 68-72 rear the axles will fit.

The brackets are the same so they will interchange with the right wheel offset. You will need posi unit axles and brakes to complete. In 1971 GM instituted a standardized corporate rear axle.

In 1970 the rear end was built in both 10 and 12 bolt versions. But this time the Camaro and Nova rears are also different because even though Nova went to the wide axle they stayed with the narrow spring perches that the narrow early rears used so a rear end that was set up for a 76 and later Nova will be the correct width for a Second Gen Camaro the spring perches will likely be wrong and fit the 68-79 Nova or 67-69 Camaro. Chevelle 64-67 has same widht as 67-69 camaro chevelle 68-72 same as 70-72 camaro.

This is just the housing only with torque arm bracket spring perches lower control arm brackets. Rearend width axle lengths. 59 rows Rear-end track width measurements of classic American cars including.

Axle lenght is 64-67 29-916 68-72 30-116. Joined Feb 19 2000. This is just the housing only with torque arm bracket spring perches lower control arm brackets rear shock mounts and panhard bar mount.

Jump to Latest Follow Status Not open for further replies. Joined Oct 17 2007 146 Posts. I have recently acquired a wrecked 87 Iroc wthe 350 TPI engine.

Non-posi Chevelle rearend now for my 37 Stude 12 tonbut I have a chance to get a mid 80s Camero rear for 10000. Discussion Starter 1 Jan 20 2009. I found a ford.

The 1970 12 bolt version will bolt into any second generation Camaro and quite often is done so in high power. The total width of the early rear end is about 60 inches and the later one is about 61 inches. Representative for comparison purposes only.

61 I have also concluded from my research a 70-72 Pontiac Tempest rear should measure 61 as well. The rear end in a 2014 SS Camaro can be replaced with a rear end of any 2014 or 2013 Camaro or SS Camaro. Measure between the mounting surfaces you will have a good rear end width measurement.

Be sure to allow for the width of the rotors in. Is it the same as 1988 Camaro rear. In this thread in this sub-forum in the.

Ford Explorer 88 Narrowed w2 short side axles. This rear end was available in a 10 bolt version only. 71 camaro 12bolt to 68 chevelle 12bolt.

The spring pads on the 64-66 rear ends are different but you can make them work. I have searched the threads and came to the conclusion that this rear should measure approx. Ford Ranger 88 5675.

81 camaro rear end width. 3 Jul 4 2003. Hawks Custom 82-2002 Camaro Firebird 88 Rear End Housing Only.

1 - 3 of 3 Posts. 30 rows Rear End Widths - - Back - -. Just concerned about.

Available in 3rd Gen 82-92 width 4th Gen 93-02 width or custom narrowed. Total widht 64-67 is 60 68-72 61. Hawks Custom 82-2002 Camaro Firebird 88 Rear End Housing Only Available in 3rd Gen 82-92 width 4th Gen 93-02 width or custom narrowed.

This Ls Swap 1990 Camaro Is A Pro Touring Street Beast